Type the cabinet.
Get every cut.

Sizes for every side, bottom, back, shelf and door, laid out on the sheet with the kerf counted. Drag the sizes, or type them, and watch the list change. The formula for any part is one tap away.

Job ticket base cabinet

Width
Height
Depth
Construction
Units
Cabinet type, fronts and shelves
Construction
Fronts, top to bottom (height is the frame opening; the last one takes what is left)
Height

The remainder

Rules: 23/32 ply, 1/8 kerf, 4 1/2 toe kick. Every one is a setting below. Defaults marked as assumptions are ones to confirm.

Build your cabinet, freeno sign-up, no download
23/32 Plywood · 96 x 48 · grain →77% of the sheet used
PLYWOOD · 23/32Side 134 1/2 x 23 1/4Side 234 1/2 x 23 1/4Toe kick boardBottom22 9/16 x 23Shelf22 7/16 x 22 3/4Stretcher 1Stretcher 2Door21 1/2 x 22Drawer front
Cut list20 parts · face frame
  • C-6Notch 4 1/2 x 3 at the front bottom corner of each side.
  • F-8Slide blocking, 25/32 thick, each side of each drawer. (2)
  • B-5Drawer slide length 22 (clear depth 23 3/4).
BUY 1 SHEET OF 1/4 PLYWOOD + BUY 1 SHEET OF 1/2 PLYWOOD + BUY 1 SHEET OF 23/32 PLYWOOD + 123 OF 3/4 SOLID WOOD · 77% YIELD
Add another cabinet

Two or more cabinets: one consolidated list, every sheet, and a clean PDF and CSV. $9 once for a project.

See the cabinet

Email me this cut list

Email delivery is not live yet, so nothing is collected here. Your list stays in this browser.

Settings

Built the way you build

Every number comes from a named setting. Change it and the list follows. Defaults marked as assumptions are ones to confirm against your own shop.

Material and carcass

Measure your sheet. Most 3/4 in plywood is 23/32 in.

Default from source. S7: 3/4 in plywood is typically 23/32 in (18 mm)
Default to confirm: assumption, no source yet
Back and joinery
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Toe kick and top
Default from source. S5: 4 1/2 in / 114 mm
Default from source. S6
Default to confirm: assumption, no source yet
Face frame
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Doors and fronts
Default from source. S4: partial overlay often 1/2 in
Default from source. S4: 1/16 gap
Default from source. S3: AWI nominal 3.2 mm
Default to confirm: assumption, no source yet
Default from source. S4 worked example: 2 1/4
Default from source. S4 worked example: 2 1/4
Default from source. S4 worked example: 3/8
Default from source. S4 worked example: 1/16
Default to confirm: assumption, no source yet
Drawers
Default from source. S2: Accuride needs at least 1/2 in (12.7 mm)
Default to confirm: assumption, no source yet
Default from source. S1 example: 1/2 in
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Sheets and saw
Default from source. S7: 4 x 8 ft retail sheet
Default from source. S7
Default from source. S8: 3.2 mm example
Default to confirm: assumption, no source yet
Edge banding
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Hardware counts

Comma separated, for example 40, 60, 80. Assumption: confirm against your hinge maker.

Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Default to confirm: assumption, no source yet
Left side · 1 of 9

Every part named and sized

Face frame or frameless. Base, wall, tall, drawer and sink cabinets. Door overlay, reveals, drawer slides and toe kick are all yours to set.

Sheet 1 · laid out

Laid out on real sheets

Parts are nested with your blade's kerf and the grain running the right way, so you know how many sheets to buy before you drive to the yard.

Job total · your prices

A list you can price from

Hardware counts, edge banding by the foot and a material total from the prices you type. Print the shop sheet, stick the labels, start cutting.

What you get for a whole project

These come from the same engine as the tool above, run on a sample four-cabinet run. They are not a customer example.

One list by material and thickness

Plywood 1/4
RefPartQtyLengthWidthBandedCabinets
ABack, 1/4123 5/1630-Base 24
BDrawer bottom, 1/4119 1/221 1/2-Base 24
CBack, 1/4117 5/1630-Drawer base 18
DDrawer bottom, 1/4313 1/221 1/2-Drawer base 18
EBack, 1/4135 5/1630-Sink base 36
FBack, 1/4129 5/1630-Wall 30

Plywood 1/4: 2 sheets

Yield 48%

PLYWOOD · 1/4Back, 1/430 x 35 5/16Back, 1/430 x 29 5/16Back, 1/430 x 23 5/16Back, 1/430 x 17 5/16Drawer bottom, 1/419 1/2 x 21 1/2Drawer bottom, 1/4 1

Guillotine layout. A better arrangement may exist. Kerf 1/8. Grain runs along the long edge of the sheet.

The CSV, as a spreadsheet reads it

material,thickness,part,cabinet_ids,qty,length,width,length_exact,width_exact,grain,band_L1,band_L2,band_W1,band_W2,rule_id
Plywood,1/4,"Back, 1/4",Base 24,1,23 5/16,30,23.3125,30,width,0,0,0,0,C-12
Plywood,1/4,"Drawer bottom, 1/4",Base 24,1,19 1/2,21 1/2,19.5,21.5,length,0,0,0,0,B-8
Plywood,1/4,"Back, 1/4",Drawer base 18,1,17 5/16,30,17.3125,30,width,0,0,0,0,C-12
Plywood,1/4,"Drawer bottom, 1/4",Drawer base 18,3,13 1/2,21 1/2,13.5,21.5,length,0,0,0,0,B-8
Plywood,1/4,"Back, 1/4",Sink base 36,1,35 5/16,30,35.3125,30,width,0,0,0,0,C-12
Plywood,1/4,"Back, 1/4",Wall 30,1,29 5/16,30,29.3125,30,width,0,0,0,0,C-12

Built the way you build

Every shop builds a little differently, so every construction number is a named setting with its default and the source of that default beside it. Where no source was found, the default is marked as an assumption for you to confirm.

Priced like a box of screws.

One cabinet is free, with no account. Pay when the job is bigger than that.

Check our numbersShops build differently. Where a rule is a trade habit and not a law, we show the default and ask you to confirm it. See a part size that looks wrong? There is a button beside every list to tell us.
One cabinet
$0
  • Full cut list on screen, no sign-up
  • All four calculators
  • On-screen project list and every sheet
  • Watermarked PDF preview
Use it free
Project Pass
$9 once
  • One whole project, up to 60 cabinets
  • Clean PDF, CSV, sheet layouts, labels
  • Unlimited edits and re-exports of it
Start a project
Shop
$15 a month

or $99 a year

  • Every job, unlimited projects
  • Saved shop standards, your name on the sheets
  • Cancel yourself, any time
Start a project

What to expect

  • 30-day money back

    On the Project Pass and the first Shop payment. No questions.

  • The maths is open

    Every number shows its formula and the setting behind it. Defaults cite their sources.

  • Who made it

    Built and supported by Paul. Email [email protected].

  • What this is not

    No CNC output, no room design, no quoting. Cost is a material estimate from the prices you type. Where it fits.

Questions

Is one cabinet really free?

Yes. Enter one cabinet and the full list of panels, face frame parts, doors and drawer parts shows on screen with no account. The four calculators are free too. Payment is only for exporting a whole project as a clean PDF and CSV.

Does it handle my joinery?

Butt and dado joints, rabbeted or applied backs, three toe kick styles, overlay or inset face frames, and side-mount or Blum TANDEM undermount slides are all settings. If your shop builds a way the settings do not cover, the list will be wrong for you, and the page says so.

Why does my 3/4 plywood show as 23/32?

Most 3/4 inch plywood measures about 23/32 inch (18 mm) because sheet goods are sold by nominal thickness. Every interior dimension depends on the real thickness, so measure your sheet and enter what the calipers say.

Can I change the reveals and gaps?

Yes. Every construction number is a named setting with its default and the source of that default shown beside it. Where no source was found, the default is marked as an assumption for you to confirm.

What if the list is wrong?

Check the first cabinet against your own method before you cut a full job. Tap any part to see its rule and the formula with your numbers. If a rule is wrong, email [email protected] with the cabinet and the part and it will be looked at.

Do you output G-code?

No. There is no CNC output, no room design and no quoting. This makes the cut list and lays it out on sheets for a table saw or track saw.

How do I cancel?

The Project Pass is a one-time payment with nothing to cancel. The Shop plan is cancelled from your account page and stays active until the end of the period you paid for.